Investigation of Hydraulic Oil Quality and Its Influence on Fuel Consumption and Environmental Performance of Motor Graders Operating under Hot and Dusty Climatic Conditions
Author Affiliations
- 1Candidate of Technical Sciences, Professor, Department of Transport Energy Devices, Tashkent State Transport University, Tashkent, Uzbekistan
- 2Tashkent State Transport University, Tashkent, Uzbekistan
Res. J. Engineering Sci., Volume 15, Issue (2), Pages 1-5, May,26 (2026)
Abstract
This study investigates the performance characteristics of UNO HV (HVLP)-46 hydraulic oil used in GR-165 series D motor graders operating under hot and dusty climatic conditions. Physicochemical and spectral analyses were conducted to evaluate viscosity stability, contamination level, wear metal concentration, and additive behavior during service. The results indicate that the used oil contains wear metals such as aluminum (Al), iron (Fe), chromium (Cr), and copper (Cu), as well as atmospheric dust contamination represented by silicon (Si). Degradation products of additives, including sulfur (S), phosphorus (P), and chlorine (Cl), were also detected. The findings demonstrate that maintaining viscosity stability reduces internal leakage within the hydraulic pump, improves volumetric and mechanical efficiency (ηv, ηm), decreases engine load, and consequently lowers fuel consumption and exhaust emissions under severe operating conditions.
References
- Smirnov, A. V. (2004)., Automotive maintenance materials., Textbook allowance/NovSU them. Yaroslav the Wise. Veliky Novgorod.
- Jerichov, B. B. (2009)., Automobile maintenance materials., Saint Petersburg State University.
- Maharramov, A. M., Akhmedova, R. A., & Akhmedova, N. F. (2009)., Petrochemicals and oil refining., Textbook for higher education. Baku: BakiUniversiteti Publishing House.
- Khakimov, B., Sharipov, Z., Alikulov, S., Alimova, Z., & Ganiboyeva, E. (2023)., Tests on the tractor installed experimental device for heating the mixture of bioethanol in diesel fuel., IOP Conference Series: Earth and Environmental Science, 1231(1), 012017.
- Zhang, C. (2008)., Study on the regularity of hydraulic oil pollution and prevention., Construction Machinery Technology and Management.
- Khamidullaevna, A. Z., Kobulovna, S. D., &Buranovna, Y. G. (2021)., Improve the physico-chemical properties of hydraulic oils by introduction of additives., The American Journal of Engineering and Technology, 3(12), 1–5.
- Kučera, M., Aleš, Z., Ivandić, Z., &Hujo, Ľ. (2013)., Possibility of hydraulic fluids with low environmental impact application in agriculture and transport machinery., Journal of Central European Agriculture, 14(1), 1–12.
- Rudnick, L. R. (2009)., Lubricant additives: chemistry and applications., CRC press.
- Ismayilov, K., et al. (2023)., The research on road dust and particles caused by traffic., AIP Conference Proceedings, 2789(1).
- Pugin, K. G. (2020)., Improving the reliability of hydraulic systems of technological machines., IOP Conference Series: Materials Science and Engineering, 971(5), 052042.
- Alimova, Z., Kholikova, N., & Kholova, S. (2020)., Improvement of properties of oils used in hydraulic systems of road-construction equipment., In IOP Conference Series: Materials Science and Engineering (Vol. 883, No. 1, p. 012167). IOP Publishing.
- Cristescu, C., Radoi, R., Dumitrescu, C., & Dumitrescu, L. (2017)., Experimental research on energy losses through friction in order to increase lifetime of hydraulic cylinders., In IOP Conference Series: Materials Science and Engineering (Vol. 174, No. 1, p. 012011). IOP Publishing.
- Alimova, Z., Tursunov, S., Khikmatov, R., & Pulatov, S. (2025)., Evaluating motor oil quality in heavily loaded quarry vehicle engines., In AIP Conference Proceedings (Vol. 3304, No. 1, p. 030041). AIP Publishing LLC.
- Yang, C., & Li, C. (2007)., Performance and application of energy saving hydraulic oil., Lubricating Oil.
- Ibrahimov, K. I., Alimova, Z. K., Turakulov, B. H., & Khalmurzaev, N. B. (2025)., Investigation of performance indicators of filtration materials used for air purification., In AIP Conference Proceedings (Vol. 3304, No. 1, p. 030058). AIP Publishing LLC.
- Shadimetov, Y., & Ayrapetov, D. (2024)., Retracted: Current issues in greening the economy., In E3S Web of Conferences (Vol. 538, p. 02010). EDP Sciences.
- Ayrapetov, D. (2024)., Technology development for producing plastic lubricant with secondary raw materials., E3S Web of Conferences, 587, 01018.
- Razzokov, Т. Х., Toshtemirov, S. J., Ergashov, G. K., Kiyamov, A. Z., Rashidov, N. S., & Alimova, Z. X. (2024)., Substantiation of the results of uneven leveling of heaps on the dryer conveyor., In E3S Web of Conferences (Vol. 494, p. 04048). EDP Sciences.
- Umirov, N., Abdurokhmonov, S., Ganiboyeva, E., & Alimova, Z. (2024)., Thermal equilibrium of the tractor and vehicle engines’ cooling systems in agriculture technological processes., In BIO Web of Conferences (Vol. 105, p. 05020). EDP Sciences.
- Sun, Y., & Wang, P. (2019)., Main influencing factors of hydraulic oil performance for construction machinery., In IOP Conference Series: Materials Science and Engineering (Vol. 677, No. 2, p. 022129). IOP Publishing.
- Alimova, Z. K., Makhamadjanov, M. A., Akhmatjanov, R. N., & Magdiev, K. I. (2025)., Development of a process for regeneration of zeolites for natural gases desulfuring., In AIP Conference Proceedings (Vol. 3304, No. 1, p. 030081). AIP Publishing LLC.
- Hakimov, R., & Ayrapetov, D. (2025)., Influence of ethanol additives on fractional composition of gasoline blends., AIP Conference Proceedings, 3256(1), 030023.
- Fozilov, G., Islam, R., Akhmedov, A., Nulloev, U., Shodmonov, S., Alimova, Z., & Yuldoshev, S. (2024)., Results of theoretical and experimental researches about determination the corn seed separator sieve parameters of the corn-thresher machine., In BIO Web of Conferences (Vol. 105, p. 04009). EDP Sciences.
- Makhamadjanov, A., & Alimova, Z. (2024)., Studying the dynamic characteristics of zeolites used in adsorption cycles for natural gas desulfuration., International Conferenceon Thermal Engineering, 1(1).
