Research Journal of Recent Sciences _________________________________________________ ISSN 2277-2502 Vol. 1(6), 70-76, June (2012) Res.J.Recent Sci. International Science Congress Association 70 Review Paper Continuous Slowing Down Approximation (CS and DA) Ranges of Electrons and Positrons for Carbon, Aluminium and CopperAgrawal Priyanka, Rathi S.K.1,2 and Verma A.S.Department of physics, B. S. A. College, Mathura 281004, INDIA Department of physics, B.S.A.C.E.T., Mathura 281004, INDIA Department of physics, Panjab University, Chandigarh 160014, INDIA Available online at: www.isca.in (Received 22nd February 2012, revised 16th March 2012, accepted 3rd April 2012)Abstract In this paper we present a relation for continuous slowing down approximation (CSDA) ranges for electrons and positrons of Carbon, Aluminium and Copper in terms of energy from 700 keV to 50000 keV and have been fitted by a second order polynomial approximation with two parameters. These parameters depend upon the atomic weight (A) and atomic number (Z) of the absorber. It has been found that the polynomial potential function gives better agreement with the available experimental data.Keywords:CSDA ranges, intermediate energy range, atomic number, atomic weight.Introduction Stopping power (SP), the inelastic mean free path (IMFP), the continuous slowing down approximation-range (CSDA-range) (R) and the energy straggling parameter are important for application such as radiation biology, electron beam lithography, and chemical analyses of surface regions of a solid and in calculation of radiation dose in radiotherapy. The principal characteristic of ionizing radiation is that it has sufficient energy to break any chemical bond and to cause ionization in all materials. Whenever the energy of a particle exceeds the ionization potential of a molecule, a collision with the molecule might lead to ionization. The knowledge of the mean free path and CSDA-range of electrons is important, especially at low energies; in line with this, number of authors has made associated studies of biological compounds1-5. For electrons of low energies, the inelastic interaction characteristics, the stopping power, the mean free path and the CSDA-range cannot be obtained directly from experiments or from Bethe’s SP theory, the latter giving accurate SPs at energies larger than 10 keV. At lower energies, the theory is, in general, invalid. For low-energy electrons, a method has been used to estimate the mentioned characteristics, based on the use of the complex dielectric function e (q, w), 'q and 'w being the momentum and energy transfer, respectively. As mentioned by Akkerman and Akkerman restrictions in these theories prevent their use for a wide range of non-organic and organic materials. To calculate the mean free path and the CSDA-range, another method is to make use of the inelastic differential cross section (IDCS) suggested by with the generalized oscillator strength (GOS). For this, the GOS has to be calculated from matrix elements that involve numerical integration of atomic wave functions. This calculation is too complicated. During the last few years, a number of optical data models have been proposed to compute the inelastic scattering of electrons, avoiding the calculation of the GOS from matrix elements. In recent years, have calculated the IMFP and the CSDA-range in DNA (thymine–adenine or cytosine–guanine) for low and intermediate energy ranges. These calculations were also studied for liquid water, guanine and organic molecules in the energy range 20 eV–10 keV1,5. In this paper, we propose a method to obtain the CSDA ranges for electrons at intermediate energy (700–50000 keV) in terms of second order polynomial fitfing. Results obtained by this procedure are compared with the available data, above 700 keV, derived from the Born–Bethe approximation. Previous Empirical Relations for CSDA Ranges The exact knowledge of range of electrons and positrons in several media is of practical interest for many applications in nuclear physics, radiation protection and semiconductor detector fabrication. The main effects produced by the passage of electrons through matter are: i. Non radiative collision process and ii. Radiative collision process. Therefore the total energy loss during the passage of electron will be the sum of these two losses. In determining CSDA ranges fluctuations in energy losses are neglected and electrons are assumed to loss energy continuously along their track with a mean energy loss per unit path length given by the stopping power. Nelms has calculated CSDA ranges using collisions Research Journal of Recent Sciences ____________________________________________________________ ISSN 2277-2502Vol. 1(6), 70-76, June (2012) Res. J. Recent Sci. International Science Congress Association 71 loss expressions. Using collision loss expressions the following equation was solved numerically by Simpson’s 1/3rd rule. dEdxdEcsda (1) Rohrlich et al have tabulated CSDA ranges of electrons and positrons for several media at different energies. Tung et alcalculated electron ranges using electron gas model. Berger and Seltzer10 published extensive tables containing CSDA ranges from 10 KeV to1000MeV. Gupta et al11 also presented an empirical formula for CSDA range but it is not applicable in low energy region. According to him an empirical equation has been derived for the csda ranges of monoenergetic electrons in the energy region 0.2-10 MeV by using the empirical relation for total stopping power. The corresponding equation for csda ranges is 1957.13230.1azszmcaz (2) Proposed relation for CSDA ranges In general the second order polynomial fitting is a simple method for searching out any empirical relation. However, the ration for continuous slowing down approximation ranges should be simple enough to get easily evaluation. One can infer from equations (1 and 2) that the CSDA ranges of electrons as well as that of positrons depend not only upon the incident kinetic energy of these particles, but also on the nature of the material through which they traverse. Tan et al12 have proposed a simple empirical relation for CSDA ranges for electrons with energies between 25 to 200 keV by the following relation, 6.15.210190cmcsda (3) Where A, Z and E are atomic weight, atomic number and energy respectively. This relation is valid for atomic numbers 30 to 92 with error comprising 2 to 10 %. The drawback of the relation is that it is valid for very small energy range and does not give any information for lower atomic number. We have plotted graphs between available CSDA ranges values vs 25.0 and data are fitting with second order polynomial equation. Which are presented in following figures 1 to 6. Using this idea we have been able to find analytically convenient and simple empirical relation for CSDA ranges of electrons and positrons in intermediate energy regions 700 to 50000 keV by the following relation, = KX2 + LX + M (4) Where = K, L and M are constants. The value of ‘X = (A/Z)E0.25’ depends on atomic weight (A), atomic number (Z) and energy (E). In equation (4) superscript (+) and (-) stands for positron and electron respectively. The values of constants are presented in table 1 (for electrons) and 2 (for positrons). Comparison between proposed and reported values Tan12 relation has been verified by proposed relation (4). This relation has been used to calculate CSDA ranges of electrons and positrons in different elements for various energies in their prescribed energy regions10. The calculated values for electrons thus obtained were compared with the standard values due to Berger and Seltzer10. In order to compare evaluated values of CSDA ranges of positrons, following method has been adopted. The evaluated values of CSDA ranges have been presented in the tables 3 and 4. This relation is valid for lower atomic numbers. We note that the values of CSDA ranges evaluated by proposed relation are in close agreement with the reported data as compared to the values reported by previous researchers so far. ConclusionFrom the above results obtained using the proposed empirical relation (4), it is quite obvious that the CSDA ranges of materials can be expressed in terms of energy and atomic number of the material. We come to the conclusion that energy of the material is key parameter for the calculation of CSDA ranges. It is also noteworthy that proposed empirical relation is simpler, widely applicable and values obtained are in better agreement with the experimental and theoretical data as compared to the empirical relations proposed by previous researchers11,12. AcknowledgementsOne of the authors (Dr. A. S. Verma, PH/08/0049) is thankful to the University Grant Commission New Delhi, India for supporting this research under the scheme of U.G.C. Dr. D.S. Kothari Post Doctoral Fellowship. References: 1.Tan Z., Xia Y., Zhao M., Liu X., Li F., Huang B. and Ji Y., Electron stopping power and mean free path in organic compounds over the energy range of 20–10 000 eV., Nucl. Instrum. Meth., B, 222, 27–43 (2004)2.Gumus H., Simple stopping power formula for low and intermediate energy electrons, Radiat. Phys. Chem. 72, 7–12 (2005) 3.Akkerman A. and Akkerman E., Characteristics of electron inelastic interactions in organic compounds and water over the energy range 20–10 000 eV. J. Appl. Phys., 86, 5809–5816 (1999)4.Dingfelder M., Hantke D., Inokuti M. and Paretzke H.G., Electron inelastic scattering cross sections in liquid water, Radiat. Phys. Chem., 53, 1–18 (1998)5.Verne J. and Pimblott M.S., Electron energy-loss distributions in solid, Dry DNA, Radiat Res., 141, 208–215 (1995) Research Journal of Recent Sciences ____________________________________________________________ ISSN 2277-2502Vol. 1(6), 70-76, June (2012) Res. J. Recent Sci. International Science Congress Association 72 6.Inokuti M., Inelastic collisions of fast charged particles with atoms and molecules-the Bethe theory revisited, Rev. Mod. Phys., 43, 297–347 (1971) 7.Nelms A., Energy loss and Ranges of electrons and positrons NBS circular no. 577 (1956)8.Rohrlich F. and Carlson B.C., Positron-Electron Differences in Energy Loss and Multiple Scattering, Phys. Rev.93, 38 (1954)9.Chaun-Jong Tung et al, CSDA Ranges of Electrons in Metals,Chinese J. Physics, 17, 1-11 (1979)10.Berger M.J. and Seltzer S.M., Tables of energy losses and ranges of electron and positron, NASA SP-3012 (1982)11.Gupta S.K., Gupta D.K. and Japanese J., Applied Physics, An Empirical Equation for the c.s.d.a. Range Difference of 0.2- to 10-MeV Electrons, 19, 1-3 (1980) 12.Tan D. and Heaton B., Applied Radiation and Isotope, Simple empirical relations for electron CSDA range and electron energy loss, 45 527-28 (1994) Table-1 Values of constants for electrons Materials K L M Regression coefficients C 6.92876 0.37645 -1.24036 0.04492 0.05889 0.00116 0.99964 Al 4.3131 0.13056 -0.84438 0.01503 0.04449 3.74316E-4 0.99995 Cu 0.79213 0.34872 -0.34752 0.03802 0.02729 8.96947E-4 0.99957 Table-2 Values of constants for positrons Materials K L M Regression coefficients C 6.94808 0.33542 -1.25451 0.04003 0.06002 0.00103 0.99973 Al 4.27644 0.13134 -0.84809 0.1512 0.04512 3.76549E-4 0.99995 Cu 0.59092 0.38837 -0.33413 0.04234 0.02762 9.98923E-4 0.9995 Table-3 Values of CSDA ranges for electrons of Carbon, Aluminium and Copper E keV C This work C [10] Al this work Al [10] Cu this work Cu [10] 700 0.401 0.316 0.369 0.354 0.342 0.409 800 0.398 0.376 0.413 0.42 0.449 0.484 900 0.409 0.437 0.464 0.487 0.552 0.56 1000 0.429 0.498 0.519 0.554 0.654 0.637 1250 0.508 0.653 0.668 0.723 0.897 0.828 1500 0.616 0.81 0.829 0.891 1.128 1.017 2000 0.878 1.121 1.164 1.223 1.560 1.389 5000 2.737 2.925 3.128 3.092 3.654 3.408 10000 5.698 5.657 5.953 5.859 6.281 6.183 15000 8.353 8.202 8.391 8.328 8.413 8.472 20000 10.775 10.59 10.576 10.56 10.268 10.43 25000 13.020 12.94 12.579 12.6 11.935 12.13 30000 15.126 14.98 14.444 14.5 13.466 13.65 35000 17.117 17.02 16.197 16.26 14.891 15.01 40000 19.012 19.12 17.859 17.89 16.230 16.24 45000 20.826 20.83 19.443 19.44 17.498 17.38 50000 22.569 22.8 20.961 20.88 18.705 18.42 Research Journal of Recent Sciences ____________________________________________________________ ISSN 2277-2502Vol. 1(6), 70-76, June (2012) Res. J. Recent Sci. International Science Congress Association 73 Table-4 Values of CSDA ranges for positrons of Carbon, Aluminium and Copper E keV C this work C [10] Al this work Al [10] Cu this work Cu [10] 700 0.394 0.315 0.365 0.355 0.33 0.411 800 0.395 0.376 0.413 0.422 0.45 0.488 900 0.409 0.438 0.466 0.49 0.56 0.567 1000 0.432 0.5 0.524 0.559 0.67 0.646 1250 0.519 0.661 0.682 0.732 0.93 0.843 1500 0.635 0.821 0.850 0.905 1.17 1.04 2000 0.910 1.141 1.197 1.247 1.63 1.427 5000 2.838 2.993 3.218 3.171 3.81 3.553 10000 5.887 5.839 6.111 6.016 6.53 6.427 15000 8.613 8.471 8.601 8.544 8.73 8.803 20000 11.098 10.94 10.831 10.83 10.64 10.82 25000 13.400 13.26 12.875 12.92 12.35 12.58 30000 15.557 15.47 14.776 14.84 13.93 14.13 35000 17.596 17.57 16.563 16.63 15.39 15.52 40000 19.537 19.57 18.256 18.3 16.76 16.78 45000 21.393 21.48 19.870 19.86 18.06 17.93 50000 23.177 23.32 21.416 21.33 19.30 18.99 101520253010152025 Y =6.92876-1.24036 X+0.05889 XCSDA ranges for C(A/Z)E0.25Figure-1 In the plot of CSDA ranges (for electrons) and (A/Z)E0.25 of Carbon lie on a polynomial line10 Research Journal of Recent Sciences ____________________________________________________________ ISSN 2277-2502Vol. 1(6), 70-76, June (2012) Res. J. Recent Sci. International Science Congress Association 74 10152025303510152025 Y =4.3131-0.84438 X+0.04449 XCSDA ranges for Al(A/Z)E0.25Figure-2 In the plot of CSDA ranges (for electrons) and (A/Z)E0.25 of Aluminium lie on a polynomial line10 101520253035101520 Y =0.79231-0.34752 X+0.02729 XCSDA ranges for Cu(A/Z)E0.25Figure-3 In the plot of CSDA ranges (for electrons) and (A/Z)E0.25 of Copper lie on a polynomial line10 Research Journal of Recent Sciences ____________________________________________________________ ISSN 2277-2502Vol. 1(6), 70-76, June (2012) Res. J. Recent Sci. International Science Congress Association 75 101520253010152025 Y =6.94808-1.25451 X+0.06002 XCSDA ranges for C(A/Z)E0.25Figure-4 In the plot of CSDA ranges (for positrons) and (A/Z)E0.25 of Carbon lie on a polynomial line10 10152025303510152025 Y =4.27644-0.84809 X+0.04512 XCSDA ranges for Al(A/Z)E0.25Figure-5 In the plot of CSDA ranges (for positrons) and (A/Z)E0.25 of Aluminium lie on a polynomial line10 Research Journal of Recent Sciences ____________________________________________________________ ISSN 2277-2502Vol. 1(6), 70-76, June (2012) Res. J. Recent Sci. International Science Congress Association 76 101520253035101520 Y =0.59092-0.33413 X+0.02762 XCSDA ranges for Cu(A/Z)E0.25Figure-6 In the plot of CSDA ranges (for positrons) and (A/Z)E0.25 of Copper lie on a polynomial line10